Alto 2000W 8" 2-Way Powered Loudspeaker
Building upon the success of Alto Professional's wildly-popular TS2 Series, TS308 is a member of their Truesonic TS3 Series that performs everything you demand in a no-compromise family of professional loudspeakers, solving every performance and installation challenge you have. In every sense, they're high-performance, with newer transducers and amplifiers that enable them to play extremely loud and clear, without restriction or compromise. They're also "high-performance" from the standpoint of concept and manufacturing—Alto was determined to make sure that every aspect of their design outperformed what it was called upon to do. So the end result are loudspeakers that reach a level of excellence and refinement that exceeds expectations.
The Truesonic TS3 series models all share a 2000-watt peak (1000-watt continuous) amplifier, a significant enhancement over the 1100-watt peak (550-watt continuous) amplifiers featured in the TS2 Series. The TS3 series boasts more advanced low-frequency drivers designed to play louder and handle more power than their already-impressive predecessors. They also include a horn-loaded high-frequency driver. This impressive transducer features an updated heat sink design that provides superb heat dissipation for exceptional power-handling, even during all-night-long concert levels. Because these improved drivers can safely handle the additional power, these models take full advantage of the increased wattage, delivering higher SPLs with lower distortion.
And if all that weren't enough already, they're now easier to use, with a newer, enhanced control panel, providing clearer control indications and detents that make for a quicker and more precise setup.
So with 2000 Watts of bi-amped power, newer drivers plus easier, more satisfying controls and setup—the TS3 range won't merely meet your requirements—it'll make you re-think what's possible.
Alto Professional TS308 Features:
- TS308 Loudspeaker
- Power Cable
- User Guide
- Safety & Warranty Manual
- Alto Professional TS308 Features:
- 2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF)
- 8" (203mm) LF driver, 2.5" (65mm) high-temperature voice coil
- HF Driver: 1.4" (35mm) neodymium magnet HF driver with precision waveguide
- High quality, lightweight, cabinet design for easy transport, set up, and installation
- Pole-mountable, wedge monitor, bracket installation, or flown application with integral M6 suspension points
- Integrated 2-channel mixer with dual XLR-¼" combo mic/line inputs, independent level controls, XLR Link output, Contour EQ switch, and Ground-Lift switch
- Custom-engineered high-efficiency class D amplifiers with passive cooling design – no fan means the speaker runs cleaner, quieter, and has greater long-term reliability
- Designed and tuned in the USA
- Alto Professional TS308 Specifications:
- Output Power: 2000 W peak (1300 LF + 700 HF) 1000 W continuous RMS (650 LF + 350 HF)
- LF Driver: 8" (203mm) LF driver, 2.5" (65mm) high-temperature voice coil
- HF Driver: 1.4" (35mm) neodymium magnet HF driver with precision waveguide
- Crossover: 2.5 kHz
- Maximum SPL: 129 dB peak, 126 dB continuous (dB SPL @ 1 m)
- Frequency Response: 62 Hz – 20 kHz (+ 3 dB)
- Frequency Range: 52 Hz – 22 kHz (-10 dB)
- Horn Coverage: 90° H x 60° V nominal
Equalization:
- (1) Contour Switch
- (1) Low and High Frequency +3 dB Boost
- Connectors:
- (2) XLR/TRS ¼" (6.35mm) combo inputs
- (1) XLR link output
- (1) IEC power cable input
- Controls:
- (2) Volume
- (1) Power on/off switch
- (1) Contour switch
- (1) Ground-Lift switch
Indicators:
- 2 x Power LED (front and rear)
- (1) Clip limiter LED
Protection:
- (1) Electronic clip
- (1) Thermal and transducer overdrive protection
Power Connection: IEC with Mains Fuse
AC Voltage Input: 100, 110-120, 220–240 V, 50/60 Hz
Enclosure: Trapezoidal, injection-molded, polypropylene enclosure, with perforated steel grille
Mounting/Installation: 36mm standard pole mount, wall or celling mount using TSB810 bracket (sold separately), flown application with integral M6 suspension points, wedge monitor
Dimensions: (H x W x D): 17.1" x 10.1" x 9.6" (434 x 256 x 245mm)
Net Weight: 20.2 lbs. (9.2 kg)
Design Origin: Designed and tuned in the USA
Available Accessories (sold separately): TSB810 Bracket, TS208 Cover
NOTE: All information is subject to change without prior notice.